How to Reset Whirlpool Washer

Published on:
This post may contain affiliate links, and we will be compensated if you buy after clicking on our links
Read our review guidelines.

When life throws a curveball and your Whirlpool washer seems to have a mind of its own, there’s a simple solution you might not be aware of. Picture a scenario where pressing a few buttons could bring back the peace in your laundry routine.

But what if those buttons hold the key to resetting your washer and saving you from a headache?

Stay tuned to uncover the secret behind how to reset Whirlpool washer and getting it back to its pristine working condition effortlessly.

When to Reset Your Whirlpool Washer

If your Whirlpool washer is experiencing performance issues such as not starting or making unusual noises, it may be time to consider resetting the appliance. These issues could be related to error codes, load imbalance, power surges, or even installing new parts.

Error codes can indicate a fault, and resetting the washer may clear them. However, if the error code persists, it could signal a faulty part that needs replacement. Load imbalance, often detected by sensors in Whirlpool washers, can cause the machine to refuse to spin. Resetting the washer can recalibrate these sensors and restore normal function.

Moreover, after a power surge or installing new parts, resetting the washer can help clear any electronic glitches and ensure smooth operation. Keep in mind that resetting your Whirlpool washer is a simple troubleshooting step that can potentially resolve various performance issues caused by electronic controls, sensors, or external factors like power surges.

7 Ways to Reset Your Whirlpool Washer

whirlpool.com

If your Whirlpool washer is acting up, don’t worry; there are a few simple ways you can reset it.

Unplug the washer, turn off the circuit breaker, or try pressing and holding certain buttons to reset the machine.

You can also attempt the dial method or open and close the washer lid to reset it.

Unplug the Washer

To reset your Whirlpool washer, begin by pressing the ‘Power’ or ‘Cancel’ button to turn off the machine.

After this, make sure to safely unplug the appliance from the electrical outlet. By disconnecting the washer from the power source, you allow the control panel to reset.

Leave the Whirlpool washer unplugged for approximately 5 minutes to ensure the reset process is effective. Once the waiting period is over, reconnect the plug back into the outlet. This action prepares the washer for a fresh start.

Turn Off the Circuit Breaker

To reset your Whirlpool washer using an alternative method, locate the circuit breaker in your home that corresponds to the laundry room or wherever your washer is located. Here’s what you need to do:

  1. Flip the breaker that’s connected to your washing machine to the ‘Off’ position.
  2. Leave it off for about 5 minutes.
  3. Flip the breaker back to the ‘On’ position.
  4. Press the ‘Power’ or ‘Start’ button to turn your washer back on.

Press and Hold “Start” and “Power” Buttons

Using a straightforward method, reset your Whirlpool washer by simultaneously pressing the ‘Start’ or ‘Pause’ and ‘Cancel’ or ‘Power’ buttons for about 5 seconds. Make sure to hold both buttons at the same time.

After the 5 seconds have passed, release the buttons. To confirm the reset, run a short cycle on your Whirlpool washing machine. This process allows the washer to restart its system and clear any errors that may have caused issues.

Remember, different models may have variations in button labels, so adapt the instructions accordingly to reset your Whirlpool washing machine effectively.

Use the Dial Method

If your Whirlpool washer features a dial instead of a digital touch panel, you can attempt to reset it using the following method.

  1. Ensure that the control panel is switched off.
  2. Rotate the dial like you’re setting it for a normal wash cycle.
  3. Turn the dial a full rotation counter clockwise (to the left) until you’re back on the initial setting you started at (e.g., “Normal”).
  4. Then, turn the dial one click to the right (clockwise), one click to the left (counter-clockwise), one click to the right (clockwise), and finally one more click to the left (counter-clockwise).

After completing the sequence, wait a moment. If the washer has reset, all the lights on the machine should turn on and then off again. To verify the reset, set the washer for a short cycle and check if it completes without issues.

Open and Close the Washer Lid

Open and close your Whirlpool washer lid repeatedly to potentially reset the appliance. For many traditional Whirlpool top-load washers without a digital display, this method can help in resetting the washer.

Ensure the washer is turned on but not actively running. Open the lid to its maximum height and firmly close it. Repeat this process six times within 12 seconds.

Following this sequence, try setting the washer for a short cycle to check if it functions correctly. This simple action of opening and closing the lid can sometimes resolve minor issues and recalibrate the washer, allowing it to operate smoothly.

Recalibrate the Washer

To recalibrate your Whirlpool washer and reset it to its default settings, follow these steps after installing new parts or experiencing a major malfunction:

  1. Unplug the washer and wait 1-2 minutes before plugging it back in.
  2. Enter Diagnostic/Test Mode by rotating the dial clockwise three clicks, then counterclockwise one click, and finally clockwise one click.
  3. After entering Diagnostic Mode, proceed to Calibration Mode by turning the dial clockwise 4 clicks until only the “Rinse” light is illuminated.
  4. Press the “Start” button to initiate the calibration process, which includes tests like filling, agitating, draining, and spinning. Once complete, the washer should exit the diagnostic mode automatically for normal use.

If “Loc” is displayed, press and hold the “control lock” button.

whirlpool.com

Press and hold the ‘control lock’ button if the display shows ‘Loc’ to reset your Whirlpool washer. If you see a padlock symbol, the control lock is likely activated.

If there’s no specific ‘control lock’ button, try pressing ‘start’ or ‘start/pause,’ holding them down for at least 5 seconds. If that doesn’t work, refer to your manual for control lock instructions.

This feature is designed to prevent accidental use, especially with children around. Simply holding the ‘control lock’ button or the ‘start’/‘start/pause’ buttons should disable this function, allowing you to resume using your washing machine as usual.

Resetting the control lock is a straightforward process to get your Whirlpool washer back in action.

How to Reset Old Cabrio Models

whirlpool.com

Step 1: Press “pause/cancel,” choose a cycle, then press start.

Select a wash cycle on the dial, then hit the start button to reset old Cabrio models. If your Whirlpool Cabrio washer is acting up, this simple step might help you clear the error code or address common problems. Here’s what you need to do:

  1. Press ‘pause/cancel’ to stop any current cycles.
  2. Choose a wash cycle on the dial.
  3. Press the start button to begin the new cycle.
  4. Wait for about a minute for the reset to take effect.

Step 2: Disconnect the power, plug it back in, and wait 10 minutes.

Disconnect the power source to your Whirlpool Cabrio washer, plug it back in, and wait for 10 minutes to reset the old models effectively. By unplugging the washing machine, you interrupt its cycle and allow the electrical charge to drain, prompting a reset within 5-10 minutes.

If the washer is hardwired or the outlet is unreachable, flip the circuit on the fuse box to cut off power. This action initiates a forced reset, crucial for resolving various issues.

During the 10-minute wait period, the machine recalibrates itself, ensuring a clean slate for the next wash cycle. Ensure the power is completely disconnected to give the washer’s circuitry ample time to reset before continuing.

Step 3: Run an empty load to help the washer recalibrate.

After waiting for 10 minutes and reconnecting the power source, proceed to run an empty load in your Whirlpool Cabrio washer to assist in recalibrating the machine.

  1. Close the lid of the washer.
  2. Plug the washer back in or flip the circuit breaker.
  3. Select the wash cycle on the dial with nothing in the drum.
  4. Allow the empty load to complete to help recalibrate the machine.

Running an empty load can often fix the problem, especially if the washer was acting faulty due to a minor issue. This step helps recalibrate the washer and can potentially save you from having to call for repairs or replace the machine, especially if it’s still under warranty.

Reasons the Washer Won’t Start

istockphoto.com

If your Whirlpool washer won’t start, it could be due to inadequate power supply, an overheated machine, or an incorrect cycle setting.

Additionally, a damaged door switch might also prevent the washer from starting.

Checking these common issues can help you troubleshoot and get your washer back up and running efficiently.

Inadequate power

To troubleshoot inadequate power causing your Whirlpool washer not to start, begin by checking if it’s properly plugged into a functioning outlet. If the outlet seems fine, the voltage may be insufficient or there could be an issue with the machine’s wiring.

  • Test the outlet with a phone charger to confirm functionality.
  • If the outlet works but the washer doesn’t, voltage may be the problem.
  • Try flipping the fuse on and off as a quick fix.
  • Contact an electrician if the issue persists for a thorough diagnosis and repair.

Overheated machine

Experiencing an overheated machine can be a reason why your Whirlpool washer won’t start, especially if you’ve been running it continuously for multiple hours. When the components of the washer are running hot, it can lead to the engine overheating.

To address this, give your washer some time to rest and allow the heat to dissipate. It’s advisable to avoid running more than 2-3 cycles in a row to prevent overheating issues.

If the engine continues to overheat, it may be necessary to contact a repair company for further assistance with the overheated washer. Regularly monitoring the temperature of your washer can help prevent such issues in the future.

Wrong cycle configuration

Incorrect cycle selection can prevent your Whirlpool washer from starting properly. If the control lock is on or the ‘delay start’ button was pressed accidentally, the washer won’t activate even when you press ‘start.’ To resolve this issue, follow these steps:

  • Reset your cycle: Unplug the washer and wait for 10 minutes before plugging it back in.
  • Check control lock: Ensure the control lock feature is off.
  • Avoid delay start: Make sure the delay start option isn’t activated.
  • Press start button: After resetting the cycle, press the start button to initiate the washer.

Damaged door switch

If you notice that your Whirlpool washer won’t start and you don’t hear a click when closing the door or can easily open the lid without resistance, the issue could be a damaged door switch. The door switch plays a crucial role in ensuring that the appliance starts only when the door is securely closed.

To address this problem, contact an appliance repair company or Whirlpool if your warranty is still valid. The door switch may need to be replaced to resolve the issue.

Ensuring that the lid is properly secured is essential for the washer to function correctly. Don’t delay in getting the door switch checked and replaced to get your Whirlpool washer back up and running efficiently.

Frequently Asked Questions about Resetting a Whirlpool Washer

How do I reset a Whirlpool washer?

To reset a Whirlpool washing machine, you can follow these steps: unplug the washer and wait for one minute, then plug it back in. Press and hold the reset button (located on the control board) for at least one minute. After that, wait for another minute before restarting the machine by pressing the start button. This should reset the washer.

What should I do if my Whirlpool washer is still not working after the reset?

If your Whirlpool washer is still not functioning properly after the reset, you may need to check the water valve, the electrical panel, and the connections. You can also refer to the tech sheet for specific instructions or watch repair videos online for guidance on troubleshooting the issue.

How can I deactivate the recalibration process on my Whirlpool washer?

If your Whirlpool washer is stuck in a recalibration loop, you can try holding the pause button for at least six times to stop the process. Then, wait for one minute before attempting to restart the machine by pressing the start button.

What steps should I take if my Whirlpool washer is not responding?

If your Whirlpool washer is not responding to commands, you can try pulling the plug, waiting for one minute, and then plugging the machine back in. Make sure to follow the user manual or seek assistance from a professional if the issue persists.

Can I reset my Whirlpool washer if it shows an error code?

If your Whirlpool washer displays an error code, you can try resetting the machine by following the standard reset procedure. If the error persists, you may need to consult the user manual or contact customer support for further assistance.

Why is it essential to reset my Whirlpool washer?

Resetting a Whirlpool washer can help resolve minor technical glitches or errors that may occur during regular use. It can also recalibrate the machine and ensure optimal performance.

Photo of author

AUTHOR

Ira Njoroge

Hey, I’m Ira Njoroge, the founder of MySpaceAffair. Early on in my life, I had a passion to embark on a mission to create a cleaner, and more organized household. With a bachelor's degree in engineering after graduating from the University of Maryland in 2015 and seven years as a General Contractor and professional cleaner, on top of my DIY Enthusiasm. I saw the need for a reliable information source for homeowners. My passion, diligence, experience, and hired professionals confirms the reliability of all the advice given in My Space Affair and I hope to provide you all with reliable and thorough content!